Replacement Chains for Petrol Chainsaws

HECHT replacement chains are a key component of every chainsaw. Even the most powerful engine cannot help if the chain is blunt, worn out or poorly chosen. Our chains are made from high-quality steel, which holds its edge for a long time and minimises vibration during cutting. Whether you are preparing a few logs for the fireplace or felling trees in the forest, a correctly chosen and sharp chain saves not only your time and energy but also the saw's motor, which does not overheat thanks to lower resistance.

Read more

Filters

Replacement Chains for Petrol Chainsaws

ORIGINAL HECHT CHAINS FOR CHAINSAWS
SAW CHAIN
HECHT 946 T, 945, 958 25Q66E
HECHT 927 up to 2015, 9920 33E40E
HECHT 9936 31E52E
HECHT 936 33E45E
HECHT 920 31E40E
HECHT 1331 33E39E
HECHT 44, 45, 46, 50, 51, 56, 944 25Q66E
HECHT 1840, 2040, 2040 QT 33E57E
HECHT 2048, 2440 33E57E
HECHT 2216 33E56E
HECHT 2240 QT, 2415 QT 33E57E
HECHT 2439, 2250 33E57E
HECHT 956 25Q72E
HECHT 927 R, 928 R, 929, 927, 9260 33E44E
RAPTOR 645, 245 25Q66E
HECHT 947, 950, 956, 951, 957 25Q66E
HECHT 975 W, 955 W, 976 W, 9504 33E33E
HECHT 1835, 1836, 3518, 941 33E53E
HECHT 2014, 2015, 939 S, 939 33E53E
WARIOR 645, RAPTOR 243 25Q64E
HECHT 2035, 2036, 2037, 9940, 2039 33E52E
HECHT 962 (OREGON 45 cm guide bar) 73E64E
HECHT 962 (OREGON 50 cm guide bar) HECHT48Y72E
HECHT 962 (HECHT 45 cm guide bar) 73E68E
HECHT 9922, 99123 14E32E
HECHT 9925 31E45E

How to Choose the Right Replacement Chain?

When choosing a new chain, three basic parameters must be considered so that it fits your guide bar perfectly:

  • Number of drive links: Total chain length (number of drive links that fit into the guide bar).

  • Chain pitch: Distance between any three consecutive rivets divided by two (e.g. 3/8", .325").

  • Gauge (drive link width): Thickness of the drive link, which must match the groove width in the guide bar (e.g. 1.1 mm, 1.3 mm or 1.5 mm). If you are unsure, information on the suitable chain can be found in your saw's manual or stamped on the side of the guide bar.

Chain Care and Sharpening

Even the best chain becomes blunt over time. If the saw starts producing fine dust instead of sawdust, or you have to push the saw during cutting, it is time to sharpen it. In the saw accessories section you will find files and grinders with which you can restore the chain's sharpness. A properly sharpened chain increases safety by significantly reducing the risk of kickback.

Chain Lubrication Is Essential

No chain can do without quality lubrication. Automatic saw lubrication protects both the chain and the guide bar from excessive friction and overheating. Use only adhesive oils intended for this purpose, which do not fling off the chain even at high speeds. Regularly checking the oil channels on the saw ensures that your replacement chain achieves maximum service life.

When Is It Time to Replace the Chain?

The chain needs to be replaced not only when it is already "ground down" (the cutting teeth are too short), but also if it shows excessive stretching that can no longer be compensated by the tensioning screw on the saw. Working with an overly stretched chain is dangerous, there is a risk of it coming off the guide bar and causing damage to the machine and injury to the operator. With a new HECHT chain you will once again enjoy a smooth and effortless cut.

Equip yourself with HECHT replacement chains and be always ready to work without unnecessary downtime.

0 produktů k porovnání
Close
0 produktů k porovnání
Compare products
No product selected.